Free preview mode
Enjoy the free questions and consider upgrading to gain full access!
300-101
Free trial
Verified
Question 26
An engineer has configured a router to use EUI-64, and was asked to document the IPv6 address of the router. The router has the following interface parameters: mac address 2201.420A.0004 subnet 2001:DB8:0:1::/64
Which IPv6 addresses should the engineer add to the documentation?
- A: 2001:DB8:0:1:01:42AF:FE0F:4
- B: 2001:DB8:0:1:FFFF:2201:420F:4
- C: 2001:DB8:0:1:FE80:2201:420F:4
- D: 2001:DB8:0:1:C601:42AE:800F:4
Question 27
If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?
- A: The lowest IP address of any physical interface
- B: The highest IP address of any physical interface
- C: The lowest IP address of any logical interface
- D: The highest IP address of any logical interface
Question 28
Which security feature can you enable to control access to the vty lines on a router?
- A: Exec-time out
- B: Logging
- C: Username and password
- D: Transport output
Question 29
A network engineer applies the command ip tcp adjust-mss <bytes> under interface configuration mode. What is the result?
- A: The probability of SYN packet truncation is increased.
- B: The UDP session is inversely affected.
- C: The probability of dropped or segmented TCP packets is decreased.
- D: The optimum MTU value for the interface is set. C
Question 30
Which two commands must you configure in the calling router to support the PPPoE client? (Choose two.)
- A: pppoe enable group
- B: peer default ip address pool
- C: pppoe-client-dial-pool-number
- D: bba-group pppoe
- E: mtu
Question 31
Which two statements about configuring Frame Relay point-to-multipoint connections are true? (Choose two)
- A: They ignore the broadcast keyword in the frame-relay DLCI mapping
- B: They require the same DLCI on each side of the link.
- C: Changing a point-to-multipoint subinterface to a different type requires the interface to be deleted and recreated.
- D: They require the frame-relay mapping command to be configured.
- E: They require inverse ARP.
Question 32
Which two statements about Frame Relay Point-to-Point connections are true? (Choose two.)
- A: Changing a point-to-point sub interface to a different type requires the device to be reloaded.
- B: They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud.
- C: The device can establish a point-to-point connection to the cloud without a DLCI.
- D: They can operate normally without a DLCI map.
- E: Each physical interface that extends to the Frame Relay cloud can support a single SVC.
Question 33
What is the purpose of configuring the router as a PPPoE client? Select the best response.
- A: To provide VPN access over L2TP
- B: To enable PPP session from the router to the termination device at the headend for metro Ethernet connectivity
- C: For DSL connectivity and removing the need for the end-user PC to run the PPPoE client software
- D: For connecting the router to a cable modem, which bridges the Ethernet frames from the router to the cable modem termination system C
Question 34
Which command instruct a PPPoE client to obtain its IP address from the PPPoe server?
- A: Interface dialer
- B: IP address negotiated
- C: PPPoE enable
- D: IP address DHCP
- E: IP address dynamic B
Question 35
Which statement about stateless and stateful IPv6 autoconfiguration are true?
- A: Both stateless and stateful autoconfiguration require additional setup
- B: Stateless autoconfiguration requires no additional setup, whereas stateful autoconfiguration requires additional setup
- C: Stateless autoconfiguration requires additional setup, whereas stateful autoconfiguration requires no additional setup
- D: Both stateless and stateful autoconfiguration require no additional setup B
Question 36
IP CEF load-sharing options (Choose three.)
- A: Tunnel
- B: Universal
- C: Include-ports
- D: Source
- E: Destination ABC
Question 37
What attribute is used to influce traffic form AS200 and AS300 so that it uses link1 to reach AS100?
- A: MED
- B: AS_path
- C: Weight
- D: Local preference
Question 38
What is true about EIGRP's redistributed static routes and summarized routes? (Choose two.)
- A: Summary routes have AD of 5
- B: Static redistributed routes have AD of 190
- C: Summary routes have AD of 20
- D: Static redistributed routes have AD of 200
Question 39
How route tags can be set? (Choose two.)
- A: Only with route-maps
- B: Only with taglists
- C: Can be set with route-maps
- D: Can be set with taglist.
- E: Only used on link state RPs.
Question 40
You have a router has some interface configured with 10Gb interface and giga interface.
Which command you use to optimize higher BW?
A.
B.
C.
D.
Question 41
Which of the below mentioned conditions form a neighbor relationship in EIGRP? (Choose three.)
- A: Hello or ACK received
- B: AS number match
- C: Hello timer match
- D: Identical metric (k values
- E: Dead Timer Match ABD
Question 42
A network engineer is disabling split horizon on a point-to-multipoint interface that is running RIPng. Under which configuration mode can split horizon be disabled?
- A: router(config-riping)#
- B: router(config-rtr)#
- C: router(config-if)#
- D: router(config)#
Question 43
Which two statements about route targets that are configured with VRF-Lite are true? (Choose two.)
- A: Route targets uniquely identify the customer routing table
- B: Route targets control the import and export of routes into a customer routing table
- C: Route targets are supported only when BGP is configured
- D: When IS-IS is configured, route targets identify the circuit level in which the customer resides
- E: When BGP is configured, route targets are transmitted as BGP standard communities
- F: Route targets allos customers to be assigned overlapping adresses
Question 44
Redistributing BGP into OSPF what statement is correct?
route-map deny 10
match ip address 10
route-map permit 20
access-list 10 permit 172.16.0.0 0.0.0.255
- A: 172.16.0.0/24 will NOT be redistributed into OSPF.
- B: 172.16.0.0/24 will be redistributed into OSPF.
- C: Routes permitted by ACL 10 will be redistributed.
- D: All routes will be filtered. A
Question 45
A route map was configured and it was distributing OSPF external routes __________.
- A: Distributing E1 only
- B: Distributing E1 and E2 using prefix list
- C: Distributing E1 and E2 using access list
- D: Distributing E2 routes
Question 46
A network engineer notices that transmission rates of senders of TCP traffic sharply increase and decrease simultaneously during periods of congestion. Which condition causes this?
- A: global synchronization
- B: tail drop
- C: random early detection
- D: queue management algorithm A
Question 47
SIMULATION -
Route.com is a small IT corporation that is attempting to implement the network shown in the exhibit. Currently the implementation is partially completed. OSPF has been configured on routers
Chicago and NewYork. The SO/O interface on Chicago and the SO/1 interface on NewYork are in
Area 0. The loopbackO interface on NewYork is in Area 1. However, they cannot ping from the serial interface of the Seattle router to the loopback interface of the NewYork router. You have been asked to complete the implementation to allow this ping.
ROUTE.com's corporate implementation guidelines require:
"¢ The OSPF process ID for all routers must be 10.
"¢ The routing protocol for each interface must be enabled under the routing process.
"¢ The routing protocol must be enabled for each interface using the most specific wildcard mask possible.
"¢ The serial link between Seattle and Chicago must be in OSPF area 21.
"¢ OSPF area 21 must not receive any inter-area or external routes.
Network Information -
Seattle -
S0/0 192.168.16.5/30 "" Link between Seattle and Chicago
Secret Password: cisco -
Chicago -
S0/0 192.168.54.9/30 "" Link between Chicago and New York
S0/1 192.168.16.6/30 "" Link between Seattle and Chicago
Secret Password: cisco -
New York -
S0/1 192.168.54.10/30 "" Link between Chicago and New York
Loopback0 172.16.189.189 -
Secret Password: cisco -
See explanation below -
Question 48
Engineer has to enable RIP on a link. Where he will issue the command?
- A: Ipv6
- B: Global
- C: Router sub command
- D: Interface subcommand
Question 49
Refer to Exhibit.
R1 is unable to ping interface S0/0 of R2.
What is the issue the configuration that is shown here?
- A: The route-target configuration command is missing.
- B: The interface IP addresses are not in the same subnet.
- C: the syntax of the ping command is wrong.
- D: The default route configuration is missing.
- E: The serial interfaces belong to the global table instead of vrf Yellow. E
Question 50
Which option describes why the EIGRP neighbors of this router are not learning routes that are received from OSPF?
- A: The subnet defined in OSPF is not part of area 0.
- B: Default metrics are not configured under EIGRP.
- C: There is no overlap in the subnets advertised.
- D: The routing protocols do not have the same AS number.
Free preview mode
Enjoy the free questions and consider upgrading to gain full access!