3V0-42.20Free trialFree trial

By vmware
Aug, 2025

Verified

25Q per page

Question 1

Which is a family of solutions for data center designs that span compute, storage, networking, and management, serving as a blueprint for a customer's Software
Defined Data Center (SDDC) implementations? (Choose the best answer.)

  • A: VMware SDDC Design
  • B: VMware Validated Design
  • C: VMware POC Design
  • D: VMware Cloud Foundation
—

Question 2

Which two benefits can be achieved using in-band management of an NSX Bare Metal Edge Node? (Choose two.)

  • A: Reduces storage requirements.
  • B: Reduces cost.
  • C: Preserves packet locality.
  • D: Reduces egress data.
  • E: Preserves switchports.
—

Question 3

An architect is helping an organization with the Physical Design of an NSX-T Data Center solution.
This information was gathered during a workshop:
✑ Any proposed solution must provide low latency.
✑ Any proposed solution must provide high throughput.
✑ Customer is running stock trading applications.
Which two selections should the architect recommend to meet high-performance workload requirements? (Choose two.)

  • A: Leverage ESXi as the compute host.
  • B: Use LACP for all uplink profiles.
  • C: Leverage KVM as the compute host.
  • D: Enable enhanced data path mode on the N-VDS.
  • E: Enable latency sensitivity mode on the N-VDS.
—

Question 4

Which selection is associated with the Review Task of the Engagement Lifecycle? (Choose the best answer.)

  • A: Gather and document requirements, assumptions, and constraints.
  • B: Build, deploy, implement, and test the design.
  • C: Measure performance against customer's objective.
  • D: Create and document the logical and physical design.
—

Question 5

An architect is helping an organization with the Logical Design of an NSX-T Data Center solution.
This information was gathered during the Assessment Phase:
✑ NSX-T will span across two sites for disaster recovery.
✑ Public Load Balancer VIP should be accessible from a secondary site.
✑ Distributed Firewall Policies should be available at a secondary site.
✑ Routing capabilities should be maintained after failure.
✑ NAT capabilities are required.
Which two selections should the architect include in their design? (Choose two.)

  • A: Use of the same ISPs across sites.
  • B: Use two separate ISPs across sites.
  • C: Use MTU to 1550 between sites.
  • D: Set MTU to 1550 between sites.
  • E: Use IP sets or groups to configure DFW rules.
—

Question 6

An architect is helping an organization with the Conceptual Design of an NSX-T Data Center solution.
Which risk is documented by an architect? (Choose the best answer.)

  • A: The security team has a firewall communication matrix documented.
  • B: The team is not trained for NSX-T but have a very strong experience with vSphere.
  • C: Open communication between different application tiers is not allowed.
  • D: Aggregate N-S throughput at any given time should be at least 10G.
—

Question 7

An architect is helping an organization with the Logical Design of an NSX-T Data Center solution.
This information was gathered during the Assessment Phase:
✑ Data between two networks connected over a public network needs to be encrypted.
✑ Certificate authentication is required.
✑ Dynamic route learning is preferred.
Which selection should the architect include in their design? (Choose the best answer.)

  • A: Deploy a Tier-0 gateway in Active/Standby mode. Configure policy-based IPSec VPN with SHA512 with RSA as the hash algorithm.
  • B: Deploy a Tier-0 gateway in Active/Active mode. Configure route-based IPSec VPN with SHA512 with RSA as the hash algorithm.
  • C: Deploy a Tier-0 gateway in Active/Standby mode. Configure route-based IPSec VPN with SHA512 with RSA as the hash algorithm.
  • D: Deploy a Tier-0 gateway in Active/Active mode. Configure policy-based IPSec VPN with SHA512 with RSA as the hash algorithm.
—

Question 8

An architect is helping an organization with the Physical Design of an NSX-T Data Center solution.
This information was gathered during a workshop:
✑ Migrating existing data center to KVM hosts.
✑ Redundancy and high availability are required.
✑ No component can be a single point of failure.
Which selection should the architect recommend? (Choose the best answer.)

  • A: Linux Bridge redundancy with Active/Active Mode and multiple pNICs with necessary binding
  • B: Linux Bridge redundancy with Active/Active Mode and single pNIC with static binding
  • C: vSS/vDS in Active/Standby Mode with necessary binding
  • D: vSS/vDS in Active/Active Mode with necessary pNICS and required binding modes
—

Question 9

An architect is helping an organization with the Conceptual Design of an NSX-T Data Center solution.
This information was gathered by the architect during the Discover Task of the Engagement Lifecycle:
✑ There are applications which use IPv6 addressing.
✑ Network administrators are not familiar with NSX-T Data Center solutions.
✑ Hosts can only be configured with two physical NICs.
✑ There is an existing management cluster to deploy the NSX-T components.
✑ Dynamic routing should be configured between the physical and virtual network.
✑ There is a storage array available to deploy NSX-T components.
Which risk was documented by the architect? (Choose the best answer.)

  • A: Network administrators are not familiar with NSX-T Data Center solutions.
  • B: Dynamic routing should be configured between the physical and virtual network.
  • C: There are applications which use IPv6 addressing.
  • D: There is a storage array available to deploy NSX-T components.
—

Question 10

An architect is helping an organization with the Physical Design of an NSX-T Data Center solution.
This information was gathered during a workshop about ESXi Host networking:
✑ A total of 50 ESXi hosts to be configured as Transport Nodes.
✑ All ESXi hosts have a dedicated 2 × Intel 10Gbps Physical Network adapter for the Overlay Traffic.
To achieve low latency, high throughput, redundancy, and performance, which two NIC teaming policies should the architect recommend? (Choose two.)

  • A: Load Balance Source MAC
  • B: Load Balance Port ID
  • C: Load Balance Source
  • D: Load Balance Source Port ID
  • E: Failover Order
—

Question 11

Which two resources can be used by an NSX architect during the Assessment Phase? (Choose two.)

  • A: vRealize Network Insight
  • B: VMware Validated Design
  • C: VMware customer references
  • D: key stakeholder interviews
  • E: application licensing
—

Question 12

Which three IPv6 features are supported in an NSX-T Data Center design? (Choose three.)

  • A: IPv6 OSPF
  • B: IPv6 static routing
  • C: IPv6 switch security
  • D: IPv6 DNS
  • E: IPv6 Distributed Firewall
  • F: IPv6 VXLAN
—

That’s the end of your free questions

You’ve reached the preview limit for 3V0-42.20

Consider upgrading to gain full access!

Page 1 of 3 • Questions 1-25 of 57
123
→

Free preview mode

Enjoy the free questions and consider upgrading to gain full access!