2V0-41.20
Free trial
Verified
Question 1
An NSX administrator noticed that the nsxcli command times out after 600 secs of idle time.
Which CLI command disables the nsxcli time out value on NSX Manager?
- A: set cli-timeout 0
- B: set cli-timeout enabled
- C: set cli-timeout disabled
- D: set cli-timeout 1
Question 2
Which CLI command should be executed on a KVM hypervisor to retrieve the VM interface UUID?
- A: virsh dumpxml <VM Name> | grep interfaceid
- B: virsh get-interface <VM Name>
- C: virsh show <VM Name> | grep interfaceid
- D: virsh list-interface <VM Name>
Question 3
What are two types of supported IPSec VPNs in NSX-T Data Center? (Choose two.)
- A: policy-based IPSec VPN
- B: Layer-7 based IPSec VPN
- C: route-based IPSec VPN
- D: Open source based IPSec VPN
- E: SSL based IPSec VPN
Question 4
Which two choices are use cases for Distributed Intrusion Detection? (Choose two.)
- A: Identify security vulnerabilities in the workloads.
- B: Use agentless antivirus with Guest Introspection.
- C: Quarantine workloads based on vulnerabilities.
- D: Identify risk and reputation of accessed websites.
- E: Gain insight about micro-segmentation traffic flows.
Question 5
An NSX administrator has been tasked with deploying a NSX Edge Virtual machine through an ISO image.
Which virtual network interface card (vNIC) type must be selected while creating the NSX Edge VM allow participation in overlay and VLAN transport zones?
- A: e1000
- B: VMXNET2
- C: VMXNET3
- D: Flexible
Question 6
What needs to be configured on a Tier-0 Gateway to make NSX Edge Services available to a VM on a VLAN-backed logical switch?
- A: Service interface
- B: Loopback Router Port
- C: Downlink interface
- D: VLAN Uplink
Question 7
Which CLI command does an NSX administrator run on the NSX Manager to generate support bundle logs if the NSX UI is inaccessible?
- A: get support-bundle file vcpnv.tgz
- B: set support-bundle file vcpnv.tgz
- C: vm-support
- D: esxcli system syslog config logger set --id=nsxmanager
Question 8
An NSX administrator would like to export syslog events that capture messages related to NSX host preparation events.
Which message ID (msgid) should be used in the syslog export configuration command as a filter?
- A: SYSTEM
- B: FABRIC
- C: GROUPING
- D: MONITORING
Question 9
Which CLI command shows syslog on NSX Manager?
- A: show log manager follow
- B: get log-file auth.log
- C: get log-file syslog
- D: /var/log/sysloq/syslog.log
Question 10
Which three protocols could an NSX administrator use to transfer log messages to a remote log server? (Choose three.)
- A: SSL
- B: HTTPS
- C: TLS
- D: UDP
- E: SSH
- F: TCP
Question 11
Which command is used to set the NSX Manager's logging-level to debug mode for troubleshooting?
- A: set service nsx-manager logging-level debug
- B: set service nsx-manager log-level debug
- C: set service manager log-level debug
- D: set service manager logging-level debug
Question 12
An NSX administrator is configuring the KVM hypervisor host as a transport node and wants to apply the Failover Order as a NIC teaming policy.
Which profile allows the administrator to configure the NIC Teaming policy as Failover Order?
- A: N-VDS/VDS Profile
- B: Transport Node Profile
- C: Host Switch Profile
- D: Uplink Profile
Question 13
The NSX Control Plane is responsible for which two functions? (Choose two.)
- A: receive and validate configuration from NSX Policy
- B: host API services
- C: propagate topology information
- D: push stateless configurations to forwarding engines
- E: maintain packet-level statistics
Question 14
An NSX administrator is using ping to check connectivity between VM1 running on ESXi1 to VM2 running on ESXi2. The ping tests fails. The administrator knows the maximum transmission unit size on the physical switch is 1600.
Which command does the administrator use to check the VMware kernel ports for tunnel end point communication?
- A: esxcli network diag ping -H <destination IP address>
- B: vmkping ++netstack=geneve -d -s 1572 <destination IP address>
- C: vmkping ++netstack=vxlan-d -s 1572 <destination IP address>
- D: esxcli network diag ping -I vmk0 -H <destination IP address>
Question 15
How is the RouterLink port created between a Tier-1 Gateway and Tier-0 Gateway?
- A: Automatically created when Tier-1 is created.
- B: Manually create a Segment and connect to both Tier-1 and Tier-0 Gateways.
- C: Manually create a Logical Switch and connect to bother Tier-1 and Tier-0 Gateways.
- D: Automatically created when Tier-1 is connected with Tier-0 from NSX UI.
Question 16
What is the most restrictive NSX-T built-in role which will allow a user to apply configuration changes on a NSX Edge?
- A: Cloud Service Administrator
- B: Network Engineer
- C: Network Operator
- D: NSX Administrator
Question 17
A customer is preparing to deploy VMware Kubernetes on an NSX-T Data Center.
What is the minimum MTU size for the UPLINK profile?
- A: 1500
- B: 1650
- C: 1550
- D: 1600
Question 18
Which tool could be used to inspect the path of a packet in the data plane?
- A: Port Connection
- B: Port Mirroring Session
- C: Netflow
- D: Traceflow
Question 19
Which two statements are true about the implementation of multicast in NSX-T Data Center? (Choose two.)
- A: Multicast routing is implemented with PIM Sparse-Mode.
- B: IGMP Snooping is used to populate multicast forwarding tables.
- C: Tier-0 gateways can be the Rendezvous Point.
- D: Multicast is supported in ESXi and KVM transport nodes.
- E: An Edge can be the Rendezvous Point.
That’s the end of your free questions
You’ve reached the preview limit for 2V0-41.20Consider upgrading to gain full access!
Free preview mode
Enjoy the free questions and consider upgrading to gain full access!