200-150
Free trial
Verified
Question 1
Which two layers of the OSI model are combined in the Internet protocol suite network access layer? (Choose two.)
- A: 1
- B: 2
- C: 3
- D: 4
- E: 5
- F: 6
- G: 7
Question 2
What is the maximum distance that is supported by Cisco passive Twinax cables?
- A: 3 m
- B: 4 m
- C: 5 m
- D: 10 m
Question 3
What is the maximum distance that is supported by Cisco active Twinax cables?
- A: 8 m
- B: 10 m
- C: 12 m
- D: 15 m
Question 4
If a Nexus switch receives a frame and does not have an entry in its MAC table for the source, which action will take place?
- A: The frame will be dropped.
- B: The frame will be flooded.
- C: The sender will be notified.
- D: The source address will be learned.
Question 5
How many IP addresses are usable for a subnet that has the address 10.6.128.0/21?
- A: 1024
- B: 2048
- C: 1022
- D: 2046
- E: 256
Question 6
What is the maximum distance that is supported between two devices that are connected via Cisco Fabric Extender Transceivers?
- A: 50 m
- B: 75 m
- C: 100 m
- D: 150 m
Question 7
What is the minimum number of fabric modules that should be installed in the Cisco Nexus 7000 chassis for N 1 redundancy using M1-Series line card?
- A: 3
- B: 4
- C: 5
- D: 6
Question 8
In an IEEE 802.3 Ethernet frame, what is the significance of the DSAP field?
- A: The DSAP field specifies the TCP or UDP port that is associated with the transport protocol.
- B: The DSAP field is only used on United States Department of Defense networks to indicate the information classification level.
- C: The DSAP field is only used in Ethernet II frames.
- D: The DSAP field indicates the network layer protocol.
Question 9
What is the maximum number of fabric modules that can be installed in a Cisco Nexus 7000 chassis?
- A: 4
- B: 5
- C: 6
- D: 7
Question 10
How many supervisor engines must a Cisco Nexus chassis contain to support the In-Service Software Update feature?
- A: 2
- B: 3
- C: 4
- D: 1
Question 11
Ethernet 1/1 is assigned IP address 10.1.1.1 with subnet mask 255.255.255.0. Which configuration is used to configure EIGRP on a Cisco Nexus 7000 switch?
- A: feature eigrp ! interface Ethernet1/1 ip address 10.1.1.1 255.255.255.0 no shutdown ! router eigrp 1 network 10.1.1.0 0.0.0.255
- B: feature eigrp ! router eigrp 1 autonomous-system 1 ! interface Ethernet1/1 ip address 10.1.1.1/24 ip router eigrp 1 no shutdown
- C: router eigrp 1 autonomous-system 1 ! interface Ethernet1/1 ip address 10.1.1.1/24 ip router eigrp 1 no shutdown
- D: feature eigrp ! interface Ethernet1/1 ip address 10.1.1.1/24 no shutdown ! router eigrp 1
Question 12
VLAN 10 is assigned IP address 10.1.1.1 with subnet mask 255.255.255.0. Which configuration is used to route the IP subnet but not form OSPF neighbors on a
Cisco Nexus 7000 switch?
- A: feature ospf ! interface Vlan10 ip address 10.1.1.1/24 no shutdown ip router ospf 1 ip passive-interface ospf 1 ! router ospf 1
- B: feature ospf ! interface Vlan10 ip address 10.1.1.1/24 no shutdown ! router ospf 1 passive-interface default no ip passive-interface Vlan10
- C: feature ospf ! interface Vlan10 ip address 10.1.1.1/24 no shutdown ! router ospf 1 ip passive-interface Vlan10
- D: feature ospf ! interface Vlan10 ip address 10.1.1.1/24 no shutdown ip router ospf 1 !
Question 13
The kickstart image is corrupted on a Cisco Nexus 7000 switch. Which procedure is used to download a new kickstart image?
- A: Boot the system and press Ctrl-] while the memory test is in progress to interrupt the boot loader.
- B: Boot the system and press the Esc key while the memory test is in progress to interrupt the boot loader.
- C: Boot the system and press the Esc key after the BIOS memory test to interrupt the boot loader.
- D: Boot the system and press Ctrl-] after the BIOS memory test to interrupt the boot loader.
Question 14
Which situation results in a flashing blue status LED on a Cisco Nexus 7000 switch I/O module?
- A: The switch has just been powered on, and the module is resetting.
- B: The module is resetting and both ejector levers are out.
- C: The module has been inserted during the initialization process.
- D: The module could not power up because of insufficient power.
- E: The operator has activated this LED to identify this module in the chassis.
Question 15
Which two features must be licensed on a Cisco Nexus 7000 Switch? (Choose two.)
- A: Layer 3
- B: Virtual Device Contexts
- C: Virtual Port Channel
- D: Fibre Channel
Question 16
Which two features must be licensed on a Cisco Nexus 5548UP Switch? (Choose two.)
- A: Virtual Port Channel
- B: Fibre Channel
- C: FabricPath
- D: iSCSI
That’s the end of your free questions
You’ve reached the preview limit for 200-150Consider upgrading to gain full access!
Free preview mode
Enjoy the free questions and consider upgrading to gain full access!