Which two statements are correct about configuring VLANs? (Choose two.)
AYou must assign an IRB interface to each VLAN.
BYou must assign a VLAN name or ID and a Layer 2 interface to the VLAN.
CYou can assign one or more VLANs to a trunk mode interface.
DYou can assign one or more VLANs to an access mode interface.
Which statement is correct about access ports?
AThey are assigned to a single VLAN.
BThey are assigned to multiple VLANs.
CThey must be connected to a router.
DThey must be connected to a firewall.
Which statement about the qualified next-hop feature is correct when configuring a static route?
AQualified next-hop is used for specifying redundant next-hops.
BQualified next-hop is used when the next-hop address is not within the route table of the local device.
CQualified next-hop is only required when a link-state protocol is configured.
DQualified next-hop uses pings to verify that the next hop is up.
By default, which two statements about trunk and access ports are correct? (Choose two.)
ATrunk ports forward untagged traffic.
BAccess ports forward untagged traffic.
CAccess ports forward tagged traffic.
DTrunk ports forward tagged traffic.
What is a function of an integrated routing and bridging (IRB) interface?
Ato route traffic between different VLANs
Bto encrypt traffic between network segments
Cto bridge traffic within the same VLAN
Dto provide Network Address Translation (NAT)
You are troubleshooting BGP routing and want to verify that you are sending a default route to peer address 10.100.25.6.
Which command would satisfy the requirement?
According to Juniper Networks, the bridge table is more commonly known as a _________.
Aforwarding table
Bforwarding bridge
Cbridging information table
Dforwarding information table
You have a problem bringing up an aggregated Ethernet interface between a spine and a leaf.
Referring to the exhibit, what is the problem?
AThe active statement must be added to LACP under the aggregated-ether-options hierarchy on one or both sides.
BThe ae interface numbers are not consistent.
CThe leaf-and-spine VLAN memberships are not consistent and should be changed to include the additional VLANs defined on spine1.
DThe leaf-and-spine MTUs are not consistent.
You have configured a static route to be used for management traffic. You want to ensure that this route is not propagated to other routers.
In this scenario, which parameter would you add to this route configuration?
Areject
Bpreference 255
Cno-readvertise
Ddiscard
Referring to the exhibit, what does the configuration do?
AIt only disables graceful restart for the BGP protocol.
BIt disables graceful restart globally for all protocols.
CIt only disables graceful restart for defined static routes.
DIt disables graceful restart for all routes defined under the routing-options hierarchy.
Which two statements about overlay networks are correct? (Choose two.)
AAn overlay network is a public network that runs on top of a private network.
BAn overlay network carries only Layer 3 traffic.
CAn overlay network is a virtual network that runs on top of a physical network.
DAn overlay network carries Layer 2 and Layer 3 traffic.
What are two advantages of spine and leaf architectures compared to legacy architectures within a data center? (Choose two.)
AContainers and hypervisors are easier to manage with spine and leaf architectures.
BSpine and leaf fabrics demonstrate better scaling features.
CBetter performance is due to low and predictable hop counts.
DAll broadcast domains become reachable, allowing easier host connectivity.
Which protocol is supported in an IP fabric underlay network?
ARSTP
BEVPN
CVXLAN
DEBGP
Which BGP attribute is used to prevent routing loops in a network?
AMED
BLOCAL_PREF
CNEXT_HOP
DAS_PATH
Which two statements about EBGP are correct? (Choose two.)
AEBGP is used between ASs.
BEBGP is used within a single AS.
CEBGP does not require a supporting IGP.
DEBGP requires a supporting IGP.
What are three valid bridging mechanisms? (Choose three.)
Afiltering
Blearning
Cflooding
Dassociating
Eadapting
Referring to the exhibit, how much time must pass before a neighbor is considered down?
A5000 ms
B2000 ms
C1000 ms
D3000 ms
In a five-stage IP fabric, what is the role of the superspine layer?
AIt ensures that every leaf device has a physical connection to every spine device in the five-stage IP fabric.
BIt establishes a common BGP autonomous system that combines multiple three-stage IP fabric spine-and-leaf nodes into one autonomous system.
CIt creates a Layer 2 underlay network between the spine nodes and leaf nodes in the five-stage IP fabric.
DIt interconnects the spine layers in different three-stage IP fabric pods in a data center at the same site or across different sites.
Which statement is correct about building an IP fabric?
AEach spine device should have a direct physical connection to every other spine device.
BEach spine device should have a direct physical connection to every leaf device.
CEach spine device must have two or more physical connections to each leaf device.
DEach spine device must have two or more physical connections to every other spine device.
Which feature should be used with a static route that has a secondary next hop with a unique route preference value?
Aretain
Bresolve
Cqualified next hop
Dinstall
What is the default time-to-live (TTL) value of an EBGP packet?
A255
B1
C32
D64
You recently switched from using a static route to reach your Internet service provider to learning the route to your provider using BGP. You want your router to use the static route as a backup route in case the BGP session with your provider fails. The BGP route to your provider is not the active route in your router's routing table.
What is causing the BGP route to behave this way?
AYour router does not have a loopback interface configured.
BYour router does not have BGP authentication enabled.
CThe static route has a lower age value than the BGP route.
DThe static route has a lower route preference value than the BGP route.
Which two statements are correct about Juniper Apstra software? (Choose two.)
AIt is intended for greenfield deployments.
BIt is only used for brownfield deployments.
CIt provides automated management of Wi-Fi access points.
DIt provides intent-based network management.
A switch receives an Ethernet frame that contains source and destination MAC addresses that are not in the Ethernet switching table.
In this scenario, which two actions does the switch perform? (Choose two.)
AThe switch floods the frame out every port in the broadcast domain except the ingress port.
BThe switch adds the source MAC address to the Ethernet switching table.
CThe switch drops the frame.
DThe switch forwards the frame to the Routing Engine.
What is the purpose of generated routes?
Ato create a route when required conditions are met
Bto create a unique routing table
Cto increase the number of route advertisements
Dto expand a single route advertisement into multiple routes
Preview
