200-301Free trial

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window
• All necessary preconfigurations have been applied
• Do not change the enable password or hostname for any device
• Save your configurations to NVRAM before moving to the next item
• Click Next at the bottom of the screen to submit this lab and move to the next question
• When Next is clicked, the lab closes and cannot be reopened

Topology

Tasks

Connectivity between four routers has been established. IP connectivity must be configured in the order presented to complete the implementation. No dynamic routing protocols are included.

1. Configure static routing using host routes to establish connectivity from router R3 to the router R1 Loopback address using the source IP of 209.165.200.230.
2. Configure an IPv4 default route on router R2 destined for router R4.
3. Configure an IPv6 default router on router R2 destined for router R4.

Which interface or port on the WLC is the default for in-band device administration and communications between the controller and access points?

Refer to the exhibit. A network administrator configures the CPE to provide internet access to the company headquarters. Traffic must be load-balanced via ISP1 and ISP2 to ensure redundancy.
Which two command sets must be configured on the CPE router? (Choose two.)

Refer to the exhibit. A network engineer updates the existing configuration on interface fastethernet1/1 switch SW1. It must establish an EtherChannel by using the same group designation with another vendor switch. Which configuration must be performed to complete the process?

Which two characteristics are representative of virtual machines (VMs)? (Choose two.)

What is the recommended switch load-balancing mode for Cisco WLCs?

What must be considered when using 802.11a?

Which type of IPv6 address is similar to a unicast address but is assigned to multiple devices on the same network at the same time?

Refer to the exhibit. An engineer configures interface fa0/1 on SW1 and SW2 to pass traffic from two different VLANs. For security reasons, company policy requires the native VLAN to be set to a nondefault value. Which configuration meets this requirement?

Refer to the exhibit A new VLAN and switch are added to the network. A remote engineer configures OldSwitch and must ensure that the configuration meets these requirements:

• accommodates current configured VLANs
• expands the range to include VLAN 20
• allows for IEEE standard support for virtual LANs

Which configuration on the NewSwitch side of the link meets these requirements?

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab closes and cannot be reopened.

Topology

Tasks

Connectivity between three routers has been established, and IP services must be configured in the order presented to complete the implementation. Tasks assigned include configuration of NAT, NTP, DHCP, and SSH services.

1. All traffic sent from R3 to the R1 Loopback address must be configured for NAT on R2. All source addresses must be translated from R3 to the IP address of Ethernet0/0 on R2, while using only a standard access list named PUBNET. To verify, a ping must be successful to the R1 Loopback address sourced from R3. Do not use NVI NAT configuration.
2. Configure R1 as an NTP server and R2 as a client, not as a peer, using the IP address of the R1 Ethernet0/2 interface. Set the clock on the NTP server for midnight on May 1, 2018.
3. Configure R1 as a DHCP server for the network 10.1.3.0/24 in a pool named NETPOOL. Using a single command, exclude addresses 1 - 10 from the range. Interface Ethernet0/2 on R3 must be issued the IP address of 10.1.3.11 via DHCP.
4. Configure SSH connectivity from R1 to R3, while excluding access via other remote connection protocols. Access for user netadmin and password N3t4ccess must be set on router R3 using RSA and 1024 bits. Verify connectivity using an SSH session from router R1 using a destination address of 10.1.3.11. Do NOT modify console.

Refer to the exhibit. A network engineer is adding another physical interface as a new member to the existing Port-Channel1 bundle. Which command set must be configured on the new interface to complete the process?

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab closes and cannot be reopened.

Topology

Tasks

All physical cabling between the two switches is installed. Configure the network connectivity between the switches using the designated VLANs and interfaces.

1. Configure VLAN 12 named Compute and VLAN 34 named Telephony where required for each task.
2. Configure Ethernet0/1 on SW2 to use the existing VLAN named Available.
3. Configure the connection between the switches using access ports.
4. Configure Ethernet0/1 on SW1 using data and voice VLANs.
5. Configure Ethernet0/1 on SW2 so that the Cisco proprietary neighbor discovery protocol is turned off for the designated interface only.

Refer to the exhibit. What is occurring on this switch?

Refer to the exhibit SW_1 and SW_12 represent two companies that are merging. They use separate network vendors. The VLANs on both sides have been migrated to share IP subnets. Which command sequence must be issued on both sides to join the two companies and pass all VLANs between the companies?

An engineer is configuring a switch port that is connected to a VoIP handset. Which command must the engineer configure to enable port security with a manually assigned MAC address of abcd.abcd.abcd on voice VLAN 4?

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked the lab closes and cannot be reopened.

Topology

Tasks

Configure IPv4 and IPv6 connectivity between two routers. For IPv4, use a /28 network from the 192.168.180.0/24 private range. For IPv6, use the first /64 subnet from the 2001:0db8:acca::/48 subnet.

1. Using Ethernet0/1 on routers R1 and R2, configure the next usable /28 from the 192.168.180.0/24 range. The network 192.168.180.0/28 is unavailable.
2. For the IPv4 /28 subnet, router R1 must be configured with the first usable host address.
3. For the IPv4 /28 subnet, router R2 must be configured with the last usable host address.
4. For the IPv6 /64 subnet, configure the routers with the IP addressing provided from the topology.
5. A ping must work between the routers on the IPv4 and IPv6 address ranges.

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked the lab closes and cannot be reopened.

Topology

Tasks

Three switches must be configured for Layer 2 connectivity. The company requires only the designated VLANs to be configured on their respective switches and permitted across any links between switches for security purposes. Do not modify or delete VTP configurations.

The network needs two user-defined VLANs configured:

VLAN 202: MARKETING

VLAN 303: FINANCE

1. Configure the VLANs on the designated switches and assign them as access ports to the interfaces connected to the PCs.
2. Configure the e0/2 interfaces on Sw1 and Sw2 as 802.1q trunks with only the required VLANs permitted.
3. Configure the e0/3 interfaces on Sw2 and Sw3 as 802.1q trunks with only the required VLANs permitted.

What is a characteristic of private IPv4 addressing?

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked the lab closes and cannot be reopened.

Topology

Tasks

Refer to the topology. All physical cabling is in place. Configure a local user account, a Named ACL (NACL), and security.

Task 1

Configure a local account on Sw101 with telnet access only on virtual ports 0-4. Use the following information:

• Username: support
• Password: max2learn
• Privilege level: Exec mode

Task 2

Configure and apply a single NACL on Sw101 using the following:

• Name: ENT_ACL
• Restrict only PC2 on VLAN 200 from pinging PC1
• Allow only PC2 on VLAN 200 to telnet to Sw101
• Prevent all other devices from telnetting from VLAN 200
• Allow all other network traffic from VLAN 200

Task 3

Configure security on interface Ethernet 0/0 of Sw102:

• Set the maximum number of secure MAC addresses to four.
• Drop packets with unknown source addresses until the number of secure MAC addresses drops below the configured maximum value. No notification action is required.
• Allow secure MAC addresses to be learned dynamically.

SIMULATION

Guidelines

This is a lab item in which tasks will be performed on virtual devices:

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked the lab closes and cannot be reopened.

Topology

Tasks

Refer to the topology. All physical cabling is in place. Configure local users accounts, modify the Named ACL (NACL), and configure DHCP Snooping. The current contents of the NACL must remain intact.

Task 1

Configure a local account on Gw1 with telnet access only on virtual ports 0-4. Use the following information:

• Username: wheel
• Password: lock3path
• Algorithm type: Scrypt
• Privilege level: Exec mode

Task 2

Configure and apply a NACL on Gw1 to control network traffic from VLAN 10:

• Name: CORP_ACL
• Allow BOOTP and HTTPS
• Restrict all other traffic and log the ingress interface, source MAC address, the packet’s source and destination IP addresses, and ports

Task 3

Configure Sw1:

• Enable DNCP Snooping for VLAN 10
• Disable DHCP Option-82 data insertion
• Enable DHCP Snooping MAC address verification
• Enable trusted interfaces

What is represented by the word "LB20" within this JSON schema?

What is represented beginning with line 1 and ending with line 5 within this JSON schema?

What is represented by the word "IDS" within this JSON schema?

What is represented in line 4 within this JSON schema?